LAMP
Type: 700 W short arc discharge
Approved model: OSRAM HTI 700/D4/75
Ballast: Electronic
Hot restrike: Yes
Socket: Double-ended SFc10-4 with key
DYNAMIC EFFECTS
Color mixing: Seamless CMY, 0 – 100%, independent 8- or 16-bit control
Color wheel: 8 replaceable filters (6 colors, 3200-4100 K CTC and UV) plus open, 8- or 16-bit control
Color temperature control: 7500 – 3200 K variable 0 – 100%, 8- or 16-bit control
Beam effects: Indexable and high-speed continuous rotating beam shaper
Dimmer/shutter: 0 – 100% dimming, 8- or 16-bit control, strobe effect variable 2 – 10 Hz, 8-bit control
Zoom: 5:1 (12.5°- 66°), 8- or 16-bit control
Pan: 540°, 8- and 16-bit control
Tilt: 246°, 8- and 16-bit control
Position correction system: Yes
OPTICS
Reflector: Glass cold light
One-tenth peak output: 17000 lumens at 50°
One-tenth peak angle: 12.5° – 66°
Total output: 18700 lumens at 50° one-tenth peak angle
Cutoff angle: 16.5° – 83°
Measurement conditions: 230 V, 50 Hz, no effects applied
Measurement test lamp: Osram HTI 700/D4/75
CONTROL AND PROGRAMMING
DMX channels: 16 (16-bit basic mode) or 23 (16-bit extended mode)
Setting and addressing: Control panel or MP-2 uploader
Movement control options: Tracking and/or vector
Receiver: Opto-isolated RS-485
Protocol: USITT DMX-512 (1990)
Firmware update: Serial upload (MUF)
CONSTRUCTION
Chassis: Steel & aluminum, shock resistant design
Housing: UV-resistant fiber-reinforced composite
Color: Black
Protection factor: IP 20
INSTALLATION
Mounting points: 2 pairs of 1/4-turn locks
Minimum distance from illuminated surface: 1.2 m (48 in.)
Minimum distance from combustible materials: 0.5 m (20 in.)
Orientation: Any
CONNECTIONS
AC power input: 3 m integral cable without power plug
DMX data in/out: 3-pin and 5-pin locking XLR
ELECTRICAL
AC power: 100-120/208-240 VAC nominal, 50/60 Hz
Power supply: Auto-ranging electronic switch-mode
Main fuse (100 – 120 V power): 15 AT (slow blow), P/N 05020027
Main fuse (208 – 240 V power): 6.3 AT (slow blow), P/N 05020020
Typical power and current
@ 100 V, 60 Hz: 1019 W, 10.3 A, PF 0.996
@ 120 V, 60 Hz: 988 W, 8.3 A, PF 0.995
@ 208 V, 60 Hz: 949 W, 4.7 A, PF 0.976
@ 230 V, 50 Hz: 944 W, 4.2 A, PF 0.973
@ 240 V, 50 Hz: 940 W, 4.0 A, PF 0.970
@ 250 V, 50 Hz: 940 W, 3.9 A, PF 0.966
PF = power factor
Note: Allow for a deviation of /- 10% from typical figures listed above: Measurements made at nominal
voltage: Local voltages can vary.
THERMAL
Maximum ambient temperature (Ta): 104° F
Maximum surface temperature, steady state, Ta: 320° F
Cooling: Filtered forced air (temperature regulated, low noise)
Total heat dissipation (calculated, 230 V, 50 Hz / 110 V, 60 Hz): 3190 BTU/hr / 3430 BTU/hr
APPROVALS
EU safety: EN 60598-1, EN 60598-2-17
EU EMC: EN 55015, EN 55103-1, EN 55103-2, EN 61000-3-2, EN 61000-3-3
US safety: ANSI/UL 1573, CE, ETL
Canadian safety: CSA C22.2 No: 166
